https://e2e.ti.com/blogs_/b/powerhouse/archive/2015/10/30/power-tips-don-t-let-a-drooping-usb-voltage-slow-down-your-charger Power Tips: Don’t let a drooping USB voltage slow down your charger Portable devices such as cellphones and tablets are capable of charging their batteries faster than ever. To obtain a fast charge time, the voltage at the charging device must be at the proper level. If it is not, the charger may reduce the charging current to a lower- (but still acceptable) level, ultimately extending the total charge time. Voltage droop across the charging cable can also cause inadequate voltage. Let’s take a look at how this might affect a universal serial bus (USB) cable and how to address potential problems. A typical USB cable interface contact resistance is approximately 30mO. Since there are four connections (two on each cable end), this represents 0.12O. Assuming a standard 24AWG wire for each power line and a 1m cable length, the total wire resistance is 0.166O. The total expected cable and contact resistance is 0.286O. If the 5V converter is designed to provide a maximum output current of 2.1A, the expected voltage drop across the cable would be 0.6V. The voltage at the end of the cable would drop to 4.4V for a fixed-converter voltage of 5.0V. This is at the lower voltage limit for USB devices, so it’s easy to see how a high-current load can create potential issues. USB cables with heavier gauge wire may help, while extra-long USB cables, with smaller gauge wire, will charge below the maximum rate. Something must be done to increase charging currents further. A common solution is to raise the output set voltage at no load, typically 5.0V, as high as possible, to 5.15V or 5.20V (5.25V maximum for USB 3.0). This solution provides adequate (although still minimal) headroom at a maximum 2.1A current. But for higher-load currents, this approach quickly runs out of steam. Another method involves using a dedicated charging port controller such as the TPS2511. This device monitors the USB data lines and automatically provides the correct electrical signatures to charge compliant devices; it also has a current-limiting function. Its current sense (/CS) pin pulls low when the output current is one-half the maximum set by a current-limiting threshold resistor. Connecting this pin through a resistor to the 5V power source’s feedback resistors (see Figure 33 in the TPS2511 data sheet) increases the output voltage, as shown in Figure 1. This reduces the voltage droop by about 50%. See the Dual-Port Automotive USB Charger Reference Design for an example design. Figure 1: Current sensing increases the output voltage at 50% load, fighting voltage droop The block diagram in Figure 2 details a method to linearly increase the converter’s output voltage to compensate for the cable losses, keeping the voltage at the end of the cable constant. This solution adds a sense resistor to monitor the output current. A differential amplifier increases the voltage across the sense resistor and uses this voltage to inject a current into the controller’s feedback (FB) pin. For more detail on this approach, see “Power Tips: Compensate for cable voltage droop”. Figure 2: Current sensing continuously adjusts the feedback to hold a steady voltage at the load These techniques are just a few ways to fight voltage droop and get the fastest charge time possible. Additional resources •Check out TI’s Power Tips blog series on Power House. •For more about this topic, see the Power Tips article, “Power Tips: Compensate for cable voltage droop.” •For similar example designs, see Automotive USB Charger with Linear Droop Compensation Reference Design and Automotive USB Battery Charging Reference Design. Sign in to Comment TI E2E™ Community Support Forums Blogs Videos Groups Site Support & Feedback Settings TI E2E™ Community Groups TI University Program Make the Switch Microcontroller Projects Motor Drive & Control Other Communities Deyisupport Designsomething.org beagleboard.org TI on Element 14 TI on TechXchangeSM Other Technical & Support Resources WEBENCH® Design Center Product Information Centers Technical Documents TI Design Network TI Technical Articles TI Training All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI. Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice. Follow Us Texas Instruments on Facebook Texas Instruments on Twitter Texas Instruments on LinkedIn Texas Instruments on Google+ TI Worldwide | Contact Us | my.TI Login | Site Map | Corporate Citizenship | mobile m.ti.com (Mobile Version) TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and embedded processors, along with software, tools and the industry’s largest sales/support staff. © Copyright 1995-2016 Texas Instruments Incorporated. All rights reserved.